SimplComp
47 days old
Not in any tracked top chart right now.
Updated 25 Oct 2026 · rankings refresh through the day
DeveloperRob Jackson
CategoryMusic
Price2.99 CAD
Released
Rating★ 0.0 (0)
Version1.0.0
Age rating4+
First seen by us
30 Sep 2026
30 Sep 2026Rating
0.0 ★
0 ratings
Measured
SimplComp on the App Store
App details
App ID
6809409909
Publisher
Rob Jackson
On the store since
Sep 2026
Under a year
Minimum OS
iOS 13.0+
iPhone 6s and later
Devices
iPhone · iPad
Universal purchase
Content rating
4+
Size
18 MB
Also listed in
Entertainment
Where it ranks now
Every top chart it appears in across 30 countries.
| Country | Charts | Rank |
|---|---|---|
| Not charting right now. | ||
Ratings
App Store, worldwide.
Rating
0.0 ★
0 ratings
Measured
Ratings
0
Measured
About SimplComp
Introduction
SimpleComp is very simple general purpose compressor that’s easy to use and very light on CPU. Sometimes you just need some basic dynamics processing that doesn’t add “character”, or that relies on sophisticated techniques or performance expensive DSP.
SimplComp was designed for those times!
SimpleComp is an AUv3 effects plugin that can run standalone, or in any AUv3 compatible host such as Logic Pro, GarageBand or AUM. SimpleComp currently runs on iPadOS / iOS (iPad & iPhone) and macOS (Intel & Silicon) and is available as a Universal Purchase from the Apple App Store.
If you’re planning on using SimpleComp on Mac / desktop, please ensure that your favourite DAW / host supports AUv3 (not just AU).
Parameters
ACTIVE - toggles the effect on or off.
IN - sets the level of the incoming signal. Typically you would leave this as 0dB, i.e unity gain. The meters to the left of the panel show the level of the incoming signal.
COMP - sets the compression threshold. Note that unlike many compressor plugins, the threshold is reduced as you turn up the control, so as you turn it up, you get more compression effect. The bar meter below this control will give an indication of how much over the threshold the input signal is.
RATIO - sets the compression ratio. A higher ratio results in a more noticeable “squashing” effect on the signal.
OUT - sets the level of the output signal. You may need to adjust this is you wish to manually make up the gain lost by the compression effect, e.g. when AUTO is off (see below).
ATK - sets the attack time of the compressor.
REL - sets the release time of the compressor.
AUTO - toggles automatic makes gain. When switched on, SimplComp will automatically adjust the gain to compensate for the gain reduction that occurs when compression is applied. This is calculated using the compression threshold and ratio.
MIX - sets the balance between the compressed and original / dry signal. This allows SimplComp to be used for parallel compression.
Factory Presets
There are a few factory presets included to get you going. The overall compression will be dependent on the level of the input signal so you will need to select an appropriate factory preset as a starting point, then adjust the COMP parameter up or down for more or less compression indicated by the bar meter below the control.
SimpleComp is very simple general purpose compressor that’s easy to use and very light on CPU. Sometimes you just need some basic dynamics processing that doesn’t add “character”, or that relies on sophisticated techniques or performance expensive DSP.
SimplComp was designed for those times!
SimpleComp is an AUv3 effects plugin that can run standalone, or in any AUv3 compatible host such as Logic Pro, GarageBand or AUM. SimpleComp currently runs on iPadOS / iOS (iPad & iPhone) and macOS (Intel & Silicon) and is available as a Universal Purchase from the Apple App Store.
If you’re planning on using SimpleComp on Mac / desktop, please ensure that your favourite DAW / host supports AUv3 (not just AU).
Parameters
ACTIVE - toggles the effect on or off.
IN - sets the level of the incoming signal. Typically you would leave this as 0dB, i.e unity gain. The meters to the left of the panel show the level of the incoming signal.
COMP - sets the compression threshold. Note that unlike many compressor plugins, the threshold is reduced as you turn up the control, so as you turn it up, you get more compression effect. The bar meter below this control will give an indication of how much over the threshold the input signal is.
RATIO - sets the compression ratio. A higher ratio results in a more noticeable “squashing” effect on the signal.
OUT - sets the level of the output signal. You may need to adjust this is you wish to manually make up the gain lost by the compression effect, e.g. when AUTO is off (see below).
ATK - sets the attack time of the compressor.
REL - sets the release time of the compressor.
AUTO - toggles automatic makes gain. When switched on, SimplComp will automatically adjust the gain to compensate for the gain reduction that occurs when compression is applied. This is calculated using the compression threshold and ratio.
MIX - sets the balance between the compressed and original / dry signal. This allows SimplComp to be used for parallel compression.
Factory Presets
There are a few factory presets included to get you going. The overall compression will be dependent on the level of the input signal so you will need to select an appropriate factory preset as a starting point, then adjust the COMP parameter up or down for more or less compression indicated by the bar meter below the control.
Latest updates
1.0.0
